Prep Center

Talk the Talk

Trade Glossary

The reading-comprehension section of these tests is really a vocabulary test. Learn the lingo and you stop feeling lost on day one.

50 terms

Journeyman

General

A worker who has completed an apprenticeship and is fully trained in a trade.

Apprentice

General

A worker learning a trade through on-the-job training and classroom instruction.

Foreman

General

The lead worker on a crew, responsible for directing the crew and reporting to the superintendent.

Superintendent

General

The person who runs the entire job site and oversees all the foremen and crews.

OSHA 10

General

A 10-hour safety certification course required to work on most commercial job sites.

OSHA 30

General

A 30-hour safety course, typically required for foremen and supervisors.

PPE

General

Personal Protective Equipment — hard hat, safety glasses, gloves, boots, vest.

Tie-off

General

Connecting your harness to an anchor point to prevent falls when working at height.

Lockout/Tagout

General

A safety procedure to isolate energy sources and tag them so equipment cannot be turned on during service.

Rough-in

General

The stage of construction when wiring, pipes, or ducts are installed before walls close up.

Trim-out

General

The finishing stage when outlets, fixtures, and final devices are installed.

Change order

General

A written change to the original contract that adds, removes, or alters work — and changes the price.

RFI

General

Request For Information — a written question from the contractor to the designer when plans are unclear.

Submittal

General

Shop drawings or product data submitted to the architect for approval before installation.

Sweep

General

Cleaning up the job site at the end of the day.

Voltage

Electrical

The electrical pressure that pushes current through a circuit, measured in volts.

Current

Electrical

The flow of electricity through a conductor, measured in amps.

Resistance

Electrical

Opposition to current flow, measured in ohms.

Ohm's Law

Electrical

Voltage = Current x Resistance. The core formula for electrical work.

Conduit

Electrical

Metal or plastic tubing that protects and routes electrical wiring.

MC cable

Electrical

Metal-clad cable — pre-wired cable in a flexible metal sheath, used for branch circuits.

Romex

Electrical

Brand name for non-metallic (NM) sheathed cable, common in residential wiring.

Junction box

Electrical

An enclosure where wires are connected and spliced, kept accessible behind a cover plate.

Circuit breaker

Electrical

A switch that automatically trips open when too much current flows, protecting the circuit.

Ground

Electrical

A safety connection to the earth that gives fault current a path away from people.

Pipefitting

Plumbing

Installing and maintaining pipe systems that carry liquids and gases under pressure.

Sweat

Plumbing

To solder a copper joint by heating it and drawing solder into the fitting.

Trap

Plumbing

A curved section of pipe that holds water and prevents sewer gas from entering the building.

Vent

Plumbing

A pipe that allows air into the drain system so water flows freely and traps stay sealed.

NPT

Plumbing

National Pipe Thread — the US standard taper thread for pipe fittings.

PSI

Plumbing

Pounds per square inch — a unit of water or gas pressure.

Valve

Plumbing

A device that starts, stops, or regulates flow through a pipe.

Refrigerant

HVAC

The fluid in an AC system that absorbs and releases heat as it cycles between liquid and gas.

Compressor

HVAC

The pump that pressurizes refrigerant and moves it through the system.

Evaporator

HVAC

The indoor coil that absorbs heat from the air, cooling the space.

Condenser

HVAC

The outdoor coil that releases heat from the refrigerant to the outside air.

Ton

HVAC

A unit of cooling capacity equal to 12,000 BTU per hour.

BTU

HVAC

British Thermal Unit — the heat needed to raise one pound of water one degree Fahrenheit.

Stud

Carpentry

A vertical framing member in a wall, usually 2x4 or 2x6 spaced 16 or 24 inches on center.

Joist

Carpentry

A horizontal framing member that supports a floor or ceiling.

Rafters

Carpentry

The sloped framing members that support a roof.

On center (OC)

Carpentry

A spacing measurement taken from the center of one member to the center of the next.

Plywood

Carpentry

A sheet good made of thin wood veneers glued in alternating grain directions.

Soffit

Carpentry

The underside of an overhang or eave.

Arc

Welding

The electric discharge between the electrode and the work that generates the heat for welding.

Bead

Welding

The deposited weld metal left along a joint.

Slag

Welding

A hard crust over a stick weld that must be chipped off to reveal the weld beneath.

TIG

Welding

Tungsten Inert Gas welding — a precise process using a non-consumable tungsten electrode.

MIG

Welding

Metal Inert Gas welding — a wire-fed process that is fast and relatively easy to learn.

Stick

Welding

Shielded Metal Arc Welding using a flux-coated electrode — rugged and used outdoors.